Brook Universal Fighting Board (PS4 PS3 XboxOne Xbox360 WiiU PC Switch NeoGeo PSClassic)
Brand : Brook
- Calculated at Checkout
The Brook UNIVERSAL FIGHTING BOARD PCB supports Xbox One, Xbox 360, PS4, PS3, Wii U PC, Switch, NEOGEO mini, PS Classic and MD mini. Low-delay design give you the best game experience
* Multi-console support(Xbox One / Xbox 360 / PS4 / PS3 / PC / Wii U / PS Mini / MD mini)
* No 8 minute timeout issue on PS4
* Build in SOCD cleaner
* Effortless installation (Screw terminal block for easy connections)
* Turbo support
* Upgradable firmware via USB
* PS4 controller touchpad button simulation
* X-Input support
* Console auto detection(PS3 / PS4 / Xbox 360 / Xbox One)
* Console manual selection(PS4 / PS3 / Xbox One / Xbox 360 / Wii U / PS Classic / MS Mini)
- Suggest be set to Xbox 360 mode on PC.
In order to prevent unexpected errors, we recommend you switch to Xbox 360 mode manually before plugging in to PC which runs on OS earlier than Win 10.
Console Manual Selection:
The Brook UNIVERSAL FIGHTING BOARD PCB support manual selection of PS4, PS3, Xbox One, Xbox 360 mode and Wii U, suggest be set to Xbox 360 mode on PC.
Notice: In order to prevent unexpected errors, we recommend you switch to Xbox 360 mode manually before plugging in to PC which runs on OS earlier than Win 10.
Step 1: Press button:
1P for PS3
2P for PS4
3P for Xbox 360
4P for Xbox One
1K for Wii U - Pokken Tournament
2K for Original Xbox
3K for Neogeo Mini
1P+2P together for PS Classic
1P+1K together for MD mini
Step 2: While pressing, connect fight stick to PC
PS2 games compatible with PS3:
Step 1. For playing PS2 game on PS3 console, press and hold 1P on the fight stick in the main page of PS2 game.
Step 2. While pressing, connect fight stick to PS3.
1. In order to prevent unexpected errors, we recommend you switch to Xbox 360 mode manually before plugging in to PC which runs on OS earlier than Win 10.
2. In the case states above, you will need to unplug our device after playing and go step 1 again after rebooting.
Verification On Nintendo Switch:
Step 1 : Check "Pro Controller Wired Communication":
On Switch, go to System Settings -> Controllers and Sensors, and turn ON Pro Controller Wired Communication.
Step 2 : Press 1K button:
1K for Wii U/Switch - Pokken Tournament and Nintendo Switch
Step 3 : While pressing 1K, connect fightstick to corresponding console
*Refer to UFB introduction page for button configuration
Verification – Switch (New)
4 steps to contact Nintendo Switch.
Press X (A) button and plug USB port to your Switch.
Select the controllers setting button on Switch with the joycon
Select the “Change Grip/Order”
The controller symbol will appear when pairing is complete.
Support PS2 games compatible with PS3
For playing PS2 game on PS3 console, press and hold 1P on the fight stick in the main page of PS2 game.
While pressing, connect fight stick to PS3
In the case states above, you will need to unplug our device after playing and go step 1 again after rebooting.
Please hold down □△ and plug it to PS Mini to use.
Support to play games on NeoGeoMini.
Hold down R2 and plug UFB to NeoGeoMini to play.
There are 5 mapping layouts. Switch between different layouts when UFB is plugged to NeoGeoMini
The layout can be memorised even if UFB is unplugged.
(1)TYPE A: PS +△ (default)
(2)TYPE B: PS +○
(3)TYPE C: PS +R1
(4)TYPE D: PS +╳
(5)TYPE E: PS +○+R2
Refer to the product introduction page for the mapping chart.
LS, RS, DP Emulate
For those who don't have LS, RS, DP switch, it's able to press combo keys for 3 seconds to switch between LS, RS, DP modes.
Pokken Tournament Pro Pad Button Config
Excellent! Super quality product. I played on xbox360, ps4 and pc, it works perfectly.
I can play everywhere and use my own stick on tournaments. I would lose, but still, it's nice to lose with your own stick!
Because I just round to rigging it up for firmware (the Share and Home buttons) until I have all the other buttons, but it updated and did what it was meant to with no fuss. Blue LED was solid. So far so good.
I have no doubt the rest of its functionality will work exactly as advertised. Once its all up and running it'll be a 5 star product.
Very easy to install great response on the joystick and buttons and easy to update would recommend this for everyone who has a arcade stick the PCB is better than the one i had in the torii arcadestick
I'm sure I could save money by not being indecisive about what console I want to play on, but this PCB is so convenient. Not sure what the latency is on it, but it's working a treat so far.
It does exactly what you would expect: it works great, it is plug and play and even updating it is an easy process. (special Kudos for the speed the company is pushing them).
So a no-brainer!
Works perfectly in all platforms, including PS4 without the 8 minutes disconnect, of course. In windows10 it works perfectly in the default XboxOne mode, but you can also force Xbox360 mode and it works too.
No lag at all in my tests.
Easy to install, you don't need a solder for the main standard cables, but you will need it for the leds, turbo, touchpad and DP mode buttons... if you are using that.
Great PCB. It works on every platform no hassle. Doesn't work in Xbox One mode on the PC? Put it into 360 mode. So happy I didn't get that 360+ board. This is the way to go. Easy and solderless (if you want the standard functions) - Let's say all in all a great experience with minimal soldering.