U-Trak Arcade Trackball With USB Interface
Brand : Ultimarc
- Calculated at Checkout
We started from the ground up rather than take an existing unsuitable unit and try to modify using add-on parts. This way we were able to address all of the problems with current designs, namely the difficulty of fitting to a wood panel, plus the poor "out of the box" spin of many trackballs.
In addition we were able to use the best quality translucent balls available. The red version is so attractive even when not lit that we decided not to bother with a solid red option. The pearl ball can be used to produce stunning multi-color lighing effects.
Mounting hardware is included, with special high-strength expanding screw sleeves which enable easy fitting with no screws visible from the top.
Can be mounted with or without bezel.
Panel thickness up to 3/4 inch (19mm).
Uses specially sourced grease-free bearings. Maximum spin right from new. No bedding-in required.
6 Bearing races, 3 stainless-steel shafts for professional durability.
Available in Cue-ball white, stunning Fireball Red translucent or amazing Pearlescent for multi-color illumination.
Full-Speed USB interface
3In Diameter ball.
RGB LED lighing PCB available.
USB Interface supports left/right mouse buttons.
4 Screws and expanding brass inserts are supplied. The inserts are designed to fit into blind holes and nothing shows from the top of the panel.
Check carefully that the supplied screws will not pierce through the top of the panel by checking the length before fitting.
Mounting without trim bezel:
Using a hole saw or fly-cutter, drill a hole 3 1/4 inch diameter (82mm). Note the vertical part of the housing is slightly conical to enable it to be molded in one piece, so to enable a perfect fit you will need to enlarge the hole from the underside of the panel slightly, using a file.
Fit the trackball with the arrow on the top of the housing pointing to the rear of the panel. Drill 4 "blind" pilot holes through the mounting holes. Then remove trackball and enlarge holes to 1/4 in (6mm). TIP: To drill blind holes use tape wrapped around drill as a depth guide. Tap the expanding inserts into place. Install trackball and screw into place.
Mounting with trim bezel:
The optimum panel thickness for this method is 5/8 in (17mm). A 3/4 inch panel can be used but the flange will sit 1/8 inch above the ball surround. Using a fly-cutter or hole saw cut a hole approx 3 3/8 inch (86mm) diameter. You may find a 3 1/2 inch or 90mm hole saw is easier to find and this will work fine.
Fit the trackball with the arrow on the top of the housing pointing to the rear of the panel. Drill 4 "blind" pilot holes through the mounting holes. Then remove trackball and enlarge holes to 1/4 in (6mm). Tap the expanding inserts into place. Install trackball and screw into place. Push the bezel over the housing. Glue can be used if required
|Conn A Red||5 Volts|
|Conn A Black||GROUND|
|Conn A Purple||X1|
|Conn A Blue||X2|
|Conn B Red||5 Volts|
|Conn B Black||GROUND|
|Conn B Yellow||Y1|
|Conn B Green||Y2|
The USB interface supports left and right mouse buttons. Suitable wires with contacts are contained in the "Mini-PAC Extension harness Pack" which can be ordered in the Mini-PAC section of our store.
The black wire shown arrowed in the above picture is not used by the trackball. This is the left button connection.
The unused contact next to this is the right button connection.
The COM terminals of the mouse button switches should be connected to a convenient ground point (Eg an I-PAC ground, or PC casing).
Pinout Of USB Interface:
Ultimarcs controls etc are used in every part of my build, joysticks, buttons, spinner, aimtrak and now the U-Trak. Its super easy to install and wire up. Is a must have for any retro fan.
Robust piece of kit comes with USB interface if you want to plug and play
Easy to setup and use as a mouse and playing games in no time!!
Perfect, absolut zu empfehlen, sehr schnelle Lieferung 1A